AirLive WN-200R Bedienungsanleitung

iWN-200HD 2.0 Mega Pixel Wireless 150Mbps IPCamera User’s Manual

1. Introduction 9AirLive WN-200HD User’s Manual 1.5.2 Bottom View 1. Audio Output Jack Audio-out Jack allows this device to output audio or a

5. Troubleshooting & FAQ 99AirLive WN-200HD User’s Manual 4. Setup the DDNS and PPPoE of Networked Device At last, users have to enter th

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 100been officially changed to 230V, 240V is within tolerances and commonly found. Au

5. Troubleshooting & FAQ 101AirLive WN-200HD User’s Manual United Kingdom 230V* 50 Hz *Outlets typically controlled by adjacent switch.

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 1025.9 UPnP Use the following steps to enable UPnP settings only if your operatin

5. Troubleshooting & FAQ 103AirLive WN-200HD User’s Manual Click Add/Remove Windows Components The following screen will appear: Select Net

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 104Select Universal Plug and Play Click Details Click Next

5. Troubleshooting & FAQ 105AirLive WN-200HD User’s Manual Please wait while Setup configures the components. Click Finish

1. Introduction AirLive WN-200HD User’s Manual 10 (1) Insert the paper clip or other tool and press and hold the button down continuously. (2) H

1. Introduction 11AirLive WN-200HD User’s Manual 3. Plug an Ethernet cable into the Camera Connect an Ethernet cable to the LAN socket located

1. Introduction AirLive WN-200HD User’s Manual 124. Connect the external power supply to Camera Connect the attached power adapter to the DC pow

2. Getting Started 13AirLive WN-200HD User’s Manual 2 2. Getting Started 2.1 IP Wizard Once you have installed the Network Camera well and p

2. Getting Started AirLive WN-200HD User’s Manual 14 When launch the IPWizard II, a searching window will pop up. IPWizard II is starting to se

2. Getting Started 15AirLive WN-200HD User’s Manual 2.1.1 View If IPWizard II finds network devices, View button will be available. Please sele

2. Getting Started AirLive WN-200HD User’s Manual 16 You could modify the relative settings of the selected device. Click “<<” button will

2. Getting Started 17AirLive WN-200HD User’s Manual In case, you do not want to change username and/or password, then just click “Submit” button

2. Getting Started AirLive WN-200HD User’s Manual 182.1.3 Wireless In case you want to change the IP related parameters of wireless interface

Copyright & Disclaimer iAirLive WN-200HD User’s Manual Copyright & Disclaimer No part of this publication may be reproduced in any form

2. Getting Started 19AirLive WN-200HD User’s Manual Click >> to next step:

2. Getting Started AirLive WN-200HD User’s Manual 20Make sure wireless setting and then submit it. Click OK to confirm these parameters, then I

2. Getting Started 21AirLive WN-200HD User’s Manual Once this step finished, IPWizard II will prompt you to unplug the Ethernet cable to activat

2. Getting Started AirLive WN-200HD User’s Manual 22To discover your device, go to your Desktop and click My Network Places. Click the target

2. Getting Started 23AirLive WN-200HD User’s Manual (1) Enable UPnP option of your NAT router To use UPnP IGD function (NAT traversal), you n

2. Getting Started AirLive WN-200HD User’s Manual 242. Type in your login name and password under “USERNAME” and “PASSWORD” textbox. For the fir

2. Getting Started 25AirLive WN-200HD User’s Manual 2.4.2 Login as Administrator If you log in the Camera as the Administrator, you can pe

3. Configure the Camera AirLive WN-200HD User’s Manual 263 3. Configure the Camera 3.1 Monitor the Image Section The image shot by the dev

3. Configure the Camera 27AirLive WN-200HD User’s Manual : Disable audio uploading function. : Enable audio uploading function. 3.6 Full

3. Configure the Camera AirLive WN-200HD User’s Manual 28 3.7.1 Digital Zoom Click Digital Zoom to active this function as above. User can dr

Copyright & Disclaimer AirLive WN-200HD User’s Manual iiFCC Statement Federal Communication Commission Interference Statement This equipmen

3. Configure the Camera 29AirLive WN-200HD User’s Manual 3.7.2 Snapshot Click Snapshot to activate this function. Press Snapshot button to

3. Configure the Camera AirLive WN-200HD User’s Manual 30Click Record to activate this function. Press Record button to start recording. The vi

3. Configure the Camera 31AirLive WN-200HD User’s Manual 3.7.5 About Click About to show this ActiveX information.

4. Monitor the Image Section AirLive WN-200HD User’s Manual 324 4. Monitor the Image Section 4.1 Monitor the Image Section This function

4. Monitor the Image Section 33AirLive WN-200HD User’s Manual 4.2 Configure via Web UI 4.2.1 Network Use this menu to configure the netwo

4. Monitor the Image Section AirLive WN-200HD User’s Manual 34IP address, Subnet mask, and Gateway: If you do not select Obtain an IP address a

4. Monitor the Image Section 35AirLive WN-200HD User’s Manual 4.2.2 Wireless If your device is a wireless model, you could assign the related

4. Monitor the Image Section AirLive WN-200HD User’s Manual 36 Step 2: Key in security key of WEP or WPA. Then click “Submit” button to activa

4. Monitor the Image Section 37AirLive WN-200HD User’s Manual In case, user wants to configure wireless settings manually, please follow the ste

4. Monitor the Image Section AirLive WN-200HD User’s Manual 38WEP settings: - Authentication: Select Open or Shared Key System Authentication

Table of Contents iiiAirLive WN-200HD User’s Manual Table of Contents 1. Introduction...

4. Monitor the Image Section 39AirLive WN-200HD User’s Manual 4.2.3 DDNS DDNS: Stands for Dynamic Domain Name Server Your Internet Service Pro

4. Monitor the Image Section AirLive WN-200HD User’s Manual 40 DDNS: To enable or disable the DDNS service here. Server name: Choose the bu

4. Monitor the Image Section 41AirLive WN-200HD User’s Manual 4.2.4 PPPoE PPPoE: Stands for Point to Point Protocol over Ethernet A standard bu

4. Monitor the Image Section AirLive WN-200HD User’s Manual 42PPPoE: To enable or disable the PPPoE service here. User name: Type the user n

4. Monitor the Image Section 43AirLive WN-200HD User’s Manual 4.2.6 UPnP UPnP is short for Universal Plug and Play, which is a networking arc

4. Monitor the Image Section AirLive WN-200HD User’s Manual 44 UPnP: To enable or disable the UPnP service here. Friendly Name: Shows the fri

4. Monitor the Image Section 45AirLive WN-200HD User’s Manual External IP address: Show the IP address and port for WAN access through Internet

4. Monitor the Image Section AirLive WN-200HD User’s Manual 46 4.2.8 IP Filter You can enter different user’s IP address which are allowing

4. Monitor the Image Section 47AirLive WN-200HD User’s Manual 4.2.9 IP Notification In case the IP address is changed, system is able to se

4. Monitor the Image Section AirLive WN-200HD User’s Manual 48 TCP Port: Set port number of TCP server. Message: The message will be sent

Table of Contents AirLive WN-200HD User’s Manual iv4.3 Camera – Adjust Camera Parameters...49 4.3.1 Picture.

4. Monitor the Image Section 49AirLive WN-200HD User’s Manual HTTP Login Password: Type the password for the HTTP server. Proxy Address: Ty

4. Monitor the Image Section AirLive WN-200HD User’s Manual 504.3.1 Picture Rotation: Turn the “Mirror” and “Vertical Flip” On or OFF. The

4. Monitor the Image Section 51AirLive WN-200HD User’s Manual White Balance: Auto: will adjust the white balance automatically. Hold: will hol

4. Monitor the Image Section AirLive WN-200HD User’s Manual 52Name: Name of the specified window. Level Defines the gray level of mask block.

4. Monitor the Image Section 53AirLive WN-200HD User’s Manual 4.4.1 System DIPS (Dynamic IP Service): To enable or disable the DIPS® (Dy

4. Monitor the Image Section AirLive WN-200HD User’s Manual 54(2) Check your Device ID from this page. This is a unique number for each device.

4. Monitor the Image Section 55AirLive WN-200HD User’s Manual Reload: Click this button; user can refresh the log information of the device. 4

4. Monitor the Image Section AirLive WN-200HD User’s Manual 56 4.4.3 Maintenance Hard Factory Default (Include the network setting): Recal

4. Monitor the Image Section 57AirLive WN-200HD User’s Manual Restore Setting: Click the “Browse” button to locate the saved backup file and t

4. Monitor the Image Section AirLive WN-200HD User’s Manual 585. Once the firmware file was selected, click “Firmware Upgrade” button. 6. The

1. Introduction 5AirLive WN-200HD User’s Manual 1 1. Introduction 1.1 Overview This camera is an inexpensive and fully scalable surveillance d

4. Monitor the Image Section 59AirLive WN-200HD User’s Manual 4.5.1 Common Text Overlay Setting: There are some important information can

4. Monitor the Image Section AirLive WN-200HD User’s Manual 604.5.2 Video Profile Name: Assign a name to the selected profile. Video T

4. Monitor the Image Section 61AirLive WN-200HD User’s Manual For VBR, user should choose the quality level to set the video quality rather than

4. Monitor the Image Section AirLive WN-200HD User’s Manual 62 4.6 Audio – Audio Parameters 4.6.1 Setting Audio: To enable or disable au

4. Monitor the Image Section 63AirLive WN-200HD User’s Manual Mute While PT: Mute the audio while pan and/or tilt motion Audio Mode: To select

4. Monitor the Image Section AirLive WN-200HD User’s Manual 64PTZ Control: Authorize this user to control PTZ function or not. Add, updat

4. Monitor the Image Section 65AirLive WN-200HD User’s Manual SMTP Server: Type the SMTP server name or the IP address of the SMTP server. T

4. Monitor the Image Section AirLive WN-200HD User’s Manual 66 Add and Del: To add or delete the motion windows. User can specify up to 10 Incl

4. Monitor the Image Section 67AirLive WN-200HD User’s Manual Sensitivity Defines the sensitivity value of motion detection. The higher value wi

4. Monitor the Image Section AirLive WN-200HD User’s Manual 684.6.6 Recording List- Files List inside SD Card This page shows the files list

1. Introduction AirLive WN-200HD User’s Manual 61.2 Features z Easy installation with setup wizard (IP Wizard II) z UPnP device discovery a

4. Monitor the Image Section 69AirLive WN-200HD User’s Manual Name: User can specify multiple FTP paths as wish. Therefore, user needs to sp

4. Monitor the Image Section AirLive WN-200HD User’s Manual 70FTP Path: Set working directory path of FTP server. FTP Passive Mode: Select

4. Monitor the Image Section 71AirLive WN-200HD User’s Manual HTTP Server z ThedevicealsocansendeventmessagetospecifiedHTTPserver. N

4. Monitor the Image Section AirLive WN-200HD User’s Manual 72Proxy Login name: Type the user name for the HTTP Proxy. Proxy Login Password

4. Monitor the Image Section 73AirLive WN-200HD User’s Manual SAMBA Login name: Type the user name for the SAMBA server. SAMBA Login Passwor

4. Monitor the Image Section AirLive WN-200HD User’s Manual 74Type: Event trigger or Schedule trigger. Enable Time: Define the feasible time

4. Monitor the Image Section 75AirLive WN-200HD User’s Manual Example 2: Send file to E-Mail server by motion triggered from Friday 18:00 to Sa

4. Monitor the Image Section AirLive WN-200HD User’s Manual 76 Example 3: Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday

4. Monitor the Image Section 77AirLive WN-200HD User’s Manual Record z User can choose the type of record file for event or schedule application

4. Monitor the Image Section AirLive WN-200HD User’s Manual 78Post-Trigger Duration: Define the maximum duration of post-alarm. Max File Siz

1. Introduction 7AirLive WN-200HD User’s Manual 1.4 Package Contents User can find the following items in the package: z This camera is the

5. Troubleshooting & FAQ 79AirLive WN-200HD User’s Manual 5 5. Troubleshooting & FAQ 5.1 Monitor the Image Section Question Ans

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 80The device will be installed and work if a firewall exists on the network. If a fir

5. Troubleshooting & FAQ 81AirLive WN-200HD User’s Manual • Maybe UPnP function of NAT router is not compatible to the IP camera. Please con

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 82• Packet Filtering of the router may prohibit access from an external network. Refe

5. Troubleshooting & FAQ 83AirLive WN-200HD User’s Manual settings prohibit downloading ActiveX controls”. The device work locally but not

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 84Pan/Tilt does not work. (including Click to Center and Preset Positioning) • Click

5. Troubleshooting & FAQ 85AirLive WN-200HD User’s Manual 5.2 PING The PING (stands for Packet Internet Groper) command is used to dete

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 865.3 Bandwidth Estimation The frame rate of video transmitted from the device de

5. Troubleshooting & FAQ 87AirLive WN-200HD User’s Manual 5.4 Specification Table Camera WN-200HD Image Device 2 Mega-pixel image sens

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 88RTP, RTCP, IGMP, PPPoE, 3GPP, Samba, ICMP Security Password protection, IP address

1. Introduction AirLive WN-200HD User’s Manual 81.5 Physical Description 1.5.1 Front View 1. Lens & Focus Ring User could use this ring

5. Troubleshooting & FAQ 89AirLive WN-200HD User’s Manual Browser IE 6.0 or later, Firefox 2.0 or later, Safari Cell Phone With 3GPP player

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 90 If you have cable or DSL service, you will most likely have a dynamically assigned

5. Troubleshooting & FAQ 91AirLive WN-200HD User’s Manual (3) Open/set Virtual Server Ports to enable remote image viewing The firewall secu

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 92 Enter valid ports in the Virtual Server section of your router. Please make sure

5. Troubleshooting & FAQ 93AirLive WN-200HD User’s Manual Host your own Networked Device and much more no matter what your computer's I

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 94 (3). After the columns show up at the left side, click “Create Account”.

5. Troubleshooting & FAQ 95AirLive WN-200HD User’s Manual (4). Fill the application agreement and necessary information. a. Username b. E-ma

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 96 (5). Check your e-mail mailbox. There will be an e-mail with a title “Your DynDNS

5. Troubleshooting & FAQ 97AirLive WN-200HD User’s Manual (6). Enter the web page http://www.dyndns.org/ again. Input your username and pass

5. Troubleshooting & FAQ AirLive WN-200HD User’s Manual 98 (10). Click the “Get Started”. (11). We could create a domain name without any