Airlive WP-203G Bedienungsanleitung

WP-203G 3 Ports Wireless Print Server User’s Manual

In the client installation procedure, after PTPP (Peer-to-Peer Printing Driver) is installed into Windows, the system will automatically (manual con

8.5 System Tools 8.5.1 Load Default You can use this page to restore the factory default settings. All of your previous setup will be clear

8.5.2 Upgrade You can upgrade new firmware for this print server in this page. Click “Browse” to select the new firmware in your storage and th

8.5.3 Backup System To backup the print server setting to a “config.bin” file, select “Backup System” and click “OK”. 97

8.5.4 Restore System To apply the setting from the backup file, click “Browse” and specify a file to restore. 98

9.Telnet Management 9.1 Introduction Print server can be configured and managed by Telnet. Through Local Area Network, or even Internet, ad

9.2 Login Execute the Telnet client tool and connect to the print server IP. telnet 192.168.2.2 Then you will be prompted to enter the username and

9.3 Get Setting Values – “get” Command “get” command is used to get the setting values of this print server. The format of “get” command is as foll

on the NetWare server PORT1_QNAME=’PQ1’ applezone The name of AppleTalk zone that this print server joins to admin# get applezone PORT1_APPLEAONE=’*

9.4 Modify Setting Values – “set” Command “set” command is used to modify the setting values of this print server. The format of “set” command is a

server joins to SNMPC The administrator contact information of this print server for SNMP set SNMPC sbdjohn@hotm ail.com SNMPL The installed location

UNIX (include HP/UX, SCO Unix, SunOS, Solaris, Unixware DECUnix, IBM AIX and others) and Linux use the system-standard LPR to print through print ser

9.5 Other Commands 9.5.1 ipconfig “ipconfig” command is used to quickly get the IP settings (IP, subnet mask, default gateway) of the print ser

9.5.4 help “help” command is used to list all telnet management commands of the print server: admin# help set argument value get argument ipconfi

10. IPP Printing 10.1 Introduction IPP (Internet Printing Protocol) Printing provides a convenient way of remote printing service by TCP/IP. The

10.2 System Setup 10.2.1 Print Server Side It is needless to do any setting on the print server side. Make sure the print server has correct I

Step4. Select “A network printer, or a printer attached to another computer”. Click “Next”. Step5. Select “Connect to a printer on the Interne

“lpt1”. One example of the URL is http://192.168.3.66:631/lpt1. After entering the URL of print server, click “Next”. Step6. Select a suit

Step7. Choose to set the print whether as a default printer or not. Click “Next”. Step8. You have added the network printer to the PC successf

112

11. LPR Setting in MAC OS LPR Printing (Line Printer Remote technology) allows Macintosh computers to connect to printers via TCP/IP. LPR Printi

Step4. Click “Add” to add the new Print Server through TCP/IP. Step5. Enter the “Printer Type”, “Printer Address” and “Queue Name” and sele

1.4 Network Printing Environment Common network environment are classified as following: Windows Peer-to-Peer Network The client’s PTPP driver wi

Printer Address: Input the IP Address of the Print Server Queue Name: The queue name of the Print Server is “lpt1” Printer Model: Select the Printer

Step7. You can print a file to check whether the Print Server is installed successfully. 116

12. UPnP Setup When the UPnP function is enabled, the print server can be detected by UPnP compliant system such as Windows XP. The print server wi

Step1. Click “Yes” on the above message or click “Start”, choose “Settings” and select “Network Connections” to enable UPnP manually. Step2.

Step3. In the “Local Area Connection Properties”, select “Advanced” option menu and click “Settings”. 119

Step4. The “Windows Firewall” screen will be popped up, select “Exceptions” option menu. Step5. Enable “UPnP Framework” from

121

13. Windows XP SP2 Setup In Windows XP SP2, XP SP2’s firewall would block the unknown communications. This print server has allowed the communicati

123

Step4. Select “Exceptions” tab and click “Add Program…”. 124

NetWare Networ k (see below) 8

Step5. Click “Browse” to add a new program. Step6. Open the “NPUtil” file from “C:\Program Files\PrintServer Utilities” (where C:\ is the system

Step8. Click “Ok”. You have completed the setting. The Windows XP SP2 will allow the incoming network connections activated by the program. 12

127 127

1.5 Contents of the User’s Manual Chapter 2 explains print server’s hardware installation and configuration. It is strongly recommended for you t

Chapter 13 In Windows XP SP2, you may not find any print server listed on the “Available Ports” in “Network Ports Quick Setup”. Please follow the ins

1.6 Firmware & Printing Function The print server provides a complete network printing solution. The feature set is listed below: PTPP (Peer-

2. Hardware Installation 1. Unpack the print server package and verify that all the items listed in the section 1.2 are provided. 2. Connect the

3. Windows Peer-to-Peer Network 3.1 System Architecture Print server supports Windows Peer-to-Peer network printing mode, which is suitable fo

3.2 Install Print Server windows utility The Print Server windows utility can be performed on Windows 95/98SE/Me/NT/2000/XP/2003 with the same

COPYRIGHT Copyright ©2006/2007 by this company. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stor

3.The “Print Server Utilities” window will be displayed. Click “Next”. 4.Click “Next” to install the utilities in the default folder or click “Chang

5.The system will start to install the utilities automatically. 6.The Print Server windows utilities Installation procedure is totally completed. a

7.The Print Server windows utilities Installation procedure is totally completed. Click “Finish”. 17

3.3 Print Server Utilities After Print Server Utilities for Administrator is completed, (choose all components during installation procedure) ,

During the client’s installation procedure, the system will automatically search for all print servers on the network, and add them into the printer

Please be aware that Network Ports Quick Setup Utility can only detect and configure all print servers on the same network, it cannot search and conf

Step3. The new remote print port is displayed as follows. In order to use the remote printing function, you will have to proceed with normal Ad

22

3.4 Windows Add Printer Procedure After adding a “Network Port” of the print server to your PC by Administrator or Client Installation Program, y

Step5. Choose the suitable “Print Server Network Port” which was created by the Administrator Installation or Client Installation process and click

CONTENTS 1. INTRODUCTION 1.1 PRODUCT INTRODUCTION...

Step7. Name your printer and setup the default printer, click “Next”. Step8. Choose to print the test page or not. It is recommended to print a

Step9. You have added the printer to the PC successfully. The information of the printer is displayed in the windows. Click “Finish”. 26

4. Windows NT/2000/2003 Network 4.1 System Architecture In Windows network environment, other than the Peer-to-Peer network printing architec

4.2 Windows NT/2000/2003 Server Installation and Setup Please follow the procedures described below for installation and construct a peer-to-peer

4.3 User Installation and Setup After server side’s installation is completed, client side will be able to find the server’s shared printer in N

5. NetWare Network 5.1 System Architecture We implemented NetWare printer sharing functionality into the print server itself, thus allowing o

Relieve the need of a workstation running the remote printer utility. Improve productivity by locating the printer near the workgroup. Each print ser

5.2 NetWare 3.x/4.x/5.x Installation & Setup Once your print server is connected to your Ethernet network, you can set it up for use with you

8. Press the Insert key to add a new NetWare print server object. The print server name can be identical to the PSxxxxxx name printed on the label

14. Select Queues Serviced by Printer, then select Printer 0 (or Printer 1, Printer 2) and press Enter. 15. Press Insert and add your newly cre

7.6 TCP/IP Configuration ... 48 7.7 Netware Print S

6. UNIX System Network 6.1 Introduction The print server is available for TCP/IP printing by Unix LPD (Line Printer Daemon) protocol. The LPD

6.2 Enable Print Server’s TCP/IP Support The default configuration of the print server is with TCP/IP support enabled. Anyway, you can configure

6.3 Setup Print Server’s IP Address The print server must have a unique IP address in order to be recognized by the network. You can set up the I

1. Optionally, assign a name corresponding to the print server’s IP address. You can add this address to the /etc/hosts file, by adding a line such

6.4 Verify Print Server’s IP Address To verify that your print server is responding to the newly assigned IP address using a PING command: ping i

6.5 Configure Remote LPD Printing on the Host The procedure you use to configure your Unix host(s) to allow printing to your network remote print

:lp=:\ :rm=203.66.191.186:\ :rp=lpt1:\ :lf=/var/spool/lpd/pserverd.log:\ :sd=/var/spool/lpd/pserverd:\ :mx#0: Lines should be indented wi

7. Configuration Utility 7.1 Introduction This chapter introduces print server’s system configuration utility in Windows environment. This ut

System Configuration: Print Server Network Ability Setting and Firmware Upgrade. Setup Wizard: Guide You Through All the Settings. Report: List the S

7.2 Search for All Available Print Server Every time when you run print server’s configuration utility, click the “Search” icon on the tool bar

9.5.1 ipconfig ... 105 9.5.2 reboot

7.3 Status of Print Server Click “Status” icon on the tool bar, the status of the current selected print server will be showed on the right sid

7.4 Setup the Print Server Click “Setup” icon on the tool bar, the setup items of the current selected print server will be showed on the righ

7.5 General Configuration Double Click “General” icon and the General configuration window will pop-up. You can see basic print server informati

7.6 TCP/IP Configuration Double Click “TCP/IP” icon and the TCP/IP configuration window will pop-up. You can configure the print server to aut

You also can select “Static IP” to manually assign “IP Address”, “Subnet Mask” and “Gateway” for the print server. Click the “DHCP Server” button to

7.7 Netware Print Server Configuration Double Click “NetWare” icon and the NetWare configuration window will pop-up. This print server supports

7.8 AppleTalk Configuration Double Click “AppleTalk” icon and the AppleTalk configuration window will pop-up. AppleTalk is a data communication

7.9 Bonjour Configuration Bonjour technology (“Rendezvous” was renamed “Bonjour” with the release of Mac OS X v10.4), also known in the industry

7.10 SNMP Configuration Double Click “SNMP” icon and the SNMP configuration window will pop up. Contact: You can enter the print server administr

7.11 SMB Configuration SMB Group Name, the name of SMB group that this print server belongs to. All PC should join the same group before they can

1. Introduction 1.1 Product Introduction Thank you for purchasing and using our print server. This print server allows your printer to become

7.12 System Configuration Double Click “System” icon and the System configuration window will pop-up. In the System configuration page, you can

Note that before you upgrade the firmware please make sure that the IP Address settings of the print server are in the same network as your computer.

7.13 Wireless Configuration If you want to use the print server through wireless LAN, please set up the print server through Ethernet first and

Infrastructure Mode: In the Infrastructure mode, you have to let the print server associate with an access point. You let the print server scan for

Ad Hoc Mode: In the Ad-Hoc mode, you can let the print server automatically associate with other wireless station or manually assign the SSID of

The list is the scanned active wireless stations. Select a wireless station in the list and click “Next”. If you cannot find the wireless station tha

You can select “64 bit” or “128 bit” length and “Hexadecimal” or “ASCII” format for the encryption key. Longer key length can provide stronger secu

y Key 1 to Key 4 – If the key length is 64-bit, enter 10-digit Hex values or 5-digit ASCII values as the encryption keys. For example: “0123456aef“ o

When you finish configuring the wireless security, click “Next” to go to next step. You can select to let the print server automatically obtain IP s

7.13 Wizard Click “Wizard” icon on the tool bar, the setup wizard item of the current selected print server will be showed on the right side of

1.2 Product Package This package contains the following components: One Print Server One Power Adapter One Antenna One Quick Installation Guide O

Step 2: Select to enable required printing protocol. Please refer to section 7.12 for detail information. Step 3: Setup the IP of this print serv

Step 4: Setup the NetWare printing. Please refer to section 7.7 for detail information. Step 5: Click “Save” to finish setting. 66

67

7.14 Report Click “Report” icon on the tool bar, the Report window will pop up. The report lists basic information of all available print server

8. Web Management 8.1 Introduction Print server can be configured and managed on the Web. Through Local Area Network, or even Internet, admin

8.2 Login You may use any Web Browser to review the status or configure the settings of the print server. After entering the IP address of the pr

8.3 Device Status 8.3.1 System System Information includes “Device Name”, “Print Server Name”, “Model Type”, “System Up Time”, “Firmware Ve

8.3.2 Printer The Print Server can communicate with the printer to get the printer information including printer manufacturer, model number, pr

8.3.3 TCP/IP This page lists all TCP/IP settings of the print server including “IP Address”, “Subnet Mask” and “Gateway”. It also lists DHCP se

8.3.4 SMB This page lists the SMB group and the pass job interval time settings of the print server. 74

1.3 Network Printing Architecture This section illustrates how print server functions and operates on the network. Before you install and use pri

8.3.5 SNMP This page lists the SNMP settings of the print server. It includes the settings of “SNMP System Contact” and “SNMP System Location”

8.3.6 NetWare This page lists NetWare settings, including “Polling Time”, “Use Bindery Mode”, “Name of the File Server” and “Port Attached

8.3.7 AppleTalk This page lists AppleTalk settings, including “AppleTalk Zone Name” and “Printer Type” of printers connected to all print por

8.3.8 Bonjour This page lists Bonjour settings, including “Printer Service Name” of each port. 78

8.4 Setup Wizard 8.4.1 System You can change the print server name and port name of the print server from here. Print Server Name, the name

8.4.1.1 Admin Password It allows you to change the password of the print server. Name is the administrator name of the print server. If you chan

8.4.1.2 Advanced Settings You can enable/disable the printing protocols and management tools from the screen. To enable the function, please sel

8.4.2 Wireless Setting If you want to use the print server through wireless LAN, please set up the print server through Ethernet first and mak

case, the print server will run in Ethernet mode. If the print server is not connected to an active network by Ethernet cable, the print server will

8.4.2.1 Site Survey You can use this “Site Survey” function to search for available access points in you location. In the list is the informati

Because print server supports IPX/SPX, NetBEUI, TCP/IP and AppleTalk network protocols, any networked computer can directly print to the print server

8.4.2.2 Encryption This print server supports WEP and WPA-PSK security mode. If you want to use WEP encryption to protect your wireless network, y

y Default Key – Select one of the four keys to encrypt your data. Only the key you select it in the “Default key” will take effect. y Key 1 – Key 4

y TKIP – TKIP (Temporal Key Integrity Protocol) changes the temporal key every 10,000 packets. This insures much greater security than the standard W

8.4.3 TCP/IP You can configure the print server to automatically get IP from DHCP server or manually specify static IP. The print server al

8.4.4 SMB You can enable/disable the SMB protocol from here. If SMB is enabled, enter the “SMB Group Name” to specify the SMB group that this

8.4.5 SNMP The print server supports SNMP configuration. If it is enabled, please set up the following parameters. SNMP System Contact: You can

8.4.6 NetWare This print server supports NetWare Bindery Printing method. The print server periodically polls the NetWare server printer queues

8.4.7 AppleTalk AppleTalk is a data communication protocol often used by Macintoshes. The print server can use these parameters to join the App

8.4.8 Bonjour “Bonjour” technology (“Rendezvous” was renamed “Bonjour” with the release of Mac OS X v10.4), also known in the industry as Zer

8.4.9 Save Settings You can click the “Save Settings” to save the settings and restart the system. 94